B. K. Exports

We offer supreme quality Ball Bearings, which are the form of rolling element bearings that use balls to maintain the division between the bearing races. Here, the ball bearings inclined to have far more lower coefficient of friction than if two flat surfaces were sliding against each other. We make these available in two broad categories, which are deep groove ball bearings and double row ball bearings. This reduces rotational friction and supports radial and axial loads. These bearings are manufactured from quality stainless steel, which are corrosion proof and can operate even under tough weather conditions.

The Double Row Ball Bearings are built for the use, where considerable amount of shaft deflection or angular misalignment are anticipated. The design comprises of two rows of ball sets with cages and a common spherical raceway in outer rings, making these bearings capable of taking angular misalignment of shaft relative to housing. These bearings allow the lowest friction of all rolling element bearings and are able to run cooler even at high operating speeds.

Features :

• Withstand combined loads with a predominant axial component
• Optimum strength
• Heavy duty usage
• Low maintenance
• Perfect finish
• Less maintenance
• Corrosion resistance
• Supports radial and axial role
• Easy to install
• High tensile strength
• Longer functional life

IMB NUMBER: CRI0868
 DIMENSIONS: 39x68x37
 USE:TRACTOR/HARVESTOR
 TYPE: ANGULAR CONTACT DOUBLE ROW / BALL BEARINGS.   WHAT ARE DAC BEARINGS

DAC BEARINGS ARE SET OR PAIR OF STEEL BALLS OR ROLLERS HELD TOGETHER BY A METAL RING, ALSO KNOW AS A RACE, THE DAC BEARINGS ARE INSIDE WHEEL HUB, ALOWING THE WHEELS TO ROTATE SMOOTHLY WHILE SUPPORTING THE VEHICLE’S WEIGHT AND ABSORB THE FORCE FROM THE ROAD. TYPES OF DAC BEARING - DAC-2RS, DAC-ZZ AND DAC WITH ABS CENSOR. DAC BEARINGS ARE ALSO AVAILABLE  WITHOUT SEAL.

DAC BEARING WITH ABS- ANTI LOCK BREAKING SYSTEM IS CALLED ABS. FUNCTION OF ABS IN THE CAR IS TO PREVENT THE WHEEL FROM LOCKING AND SKIDDING WHEN THE BRAKES ARE SUDDENLY APPLIED WITH FORCE, ESPECIALLY ON SLIPPERY ROADS. IT HELPS KEEP DRIVER IN CONTROL OF STEERING AND VEHICLE FROM SKIDDING.

DAC – 2RS MEANS TWO RUBBER SEAL ON THE BOTH SIDE, RS IS THE BEARING CODE FOR RUBBER SEAL IN THE BEARING. 2RS MEANS RUBBER SEAL ON BOTH SIDES. . IT FUNCTION IS TO STOP LEAKING OF GREASE AND KEEP OUT THE DUST, DIRT AND DEBRIS.

IMB- DAC- ZZ, IS THE DOUBLE ROW CONTACT BALL BEARING.THE METAL SHEET IS PRESSED INTO THE OUTER RING OF THE BEARING, IT IS NON REMOVABLE METAL SHEET ON BOTH SIDE. IT FUNCTION IS TO STOP LEAKING OF GREASE AND KEEP OUT THE DUST, DIRT AND DEBRISIMB- DU BEARINGS – DU BEARINGS CAN BE IN SINGLE OR DOUBLE ROW TAPER BEARING FOR E.G 30315 DU IS SINGLE ROW TAPER BEARING. DU BEARINGS ARE RIGID AND HAVE HIGH LOAD CAPACITY, WHICH MAKES THEM SUITABLE FOR HEAVY RADIAL AND AXIAL LOADS. THIS BEARINGS ARE USED IN automotive industry and heavy engineering, The inner and outer rings and rollers are tapered, and the raceways converge at a single point on the bearing axis. 

WHAT ARE BEARINGS - Bearings are "parts that assist objects' rotation bearings assist the shaft that rotates inside the machinery smoothly.
Bearings are used in automobiles, airplanes, electric generators and so on. Also used in household appliances. The function of the Bearings is to rotating shafts of the wheels, gears, turbines, rotors, etc. in those machines, allowing them to rotate more smoothly.. The function of the bearings is to reduce friction, make rotation smoother and to protect the part that supports the rotation, and maintain the correct position for the rotating shaft.
DIFFERENT TYPES OF BEARINGS – Ball bearings, Taper, Cylindrical, Spherical, Kingpin, Needle and DAC Bearings.

IMB DG BEARING ARE DEEP GROVE BALL BEARINGS =, THEY ARE AVIABLE IN SINGLE AND DOUBLE ROW DESIGNS. DG BEARING ARE AVAILABLE WITH AND WITHOUT SEAL.

IMB NUMBER: DAC35620040 ABS / 572813
 DIMENSIONS: 35.00x61.80x40.00
 APPLICATION: FRONT WHEEL ABS BEARING FOR CELERIO AND IGNIS

IMB number: sc07a42c4 (33x55x15)
 dimension: 33x55x15
 application: intermediate shaft of honda civic and other honda models
 type:ball bearings

IMB NUMBER: L359-224523 / 271526203102/103
 DIMENSIONS: 70x100x16
 TYPE: DEEP GROVE BALL BEARING

We are leading manufacturer of Insert unit for Volvo trucks and buses. Insert unit are mainly used in front and rear volvo FM400, FM440, B10, B12. We are manufacturer of below mentioned series-

F566425
F566426
F566427
F568879
800792
581079
805165

We are engaged in offering this product to our clients. Our range of all products is widely appreciated by our clients.

IMB - BALL BEARINGS FOR AUTOMOTIVE AND INDUSTRIAL USE.
OEM NUMBER - 06 31420 0302, EIADKN-7025A, M20121, 9920 03 1890, 20973340,  954528, M 2293
DIMENSIONS - 55 X 100 X 21,   The ball bearings are made of two rings or races, with steel balls in between, it helps reduces friction and allows moving parts of the machine to roll over each other. It basically reduce the friction, which increase the life of the machine or machine parts. Ball bearings are used in day to day products, like house hold electrical appliances, water pumps automotive and many other equipment’s.  Ball bearings are made up of variety of materials like Bearing steel, carbon steel, chrome steel, aluminium, tungsten carbide, platinum and many other materials.WHAT ARE BEARINGS - Bearings are "parts that assist objects' rotation bearings assist the shaft that rotates inside the machinery smoothly. Bearings are used in automobiles, airplanes, electric generators and so on. Also used in household appliances.The function of the Bearings is to rotating shafts of the wheels, gears, turbines, rotors, etc. in those machines, allowing them to rotate more smoothly.. The function of the bearings is to reduce friction, make rotation smoother and to protect the part that supports the rotation, and maintain the correct position for the rotating shaft.DIFFERENT TYPES OF BEARINGS – Ball bearings, Taper, Cylindrical, Spherical, Kingpin, Needle and DAC Bearings. WHAT ARE TAPER BEARINGS AND ITS FUNCTIONS – Tapered roller bearings supports axial forces, as well as radial forces. The taper bearings consist of Cone, Cup, Cage and Rollers.

Tapered roller bearings are made up of cone assembly and a cup. The cone assembly consists of the inner ring, the rollers, and a cage that retains and evenly spaces the rollers. The cup is simply the outer ring. Internal clearance is established during mounting by the axial position of the cone relative to the cup, although preloaded installations without clearance are common.
Cylindrical Roller Bearings – As name suggest the rollers are in cylindrical in shape. This bearings are design for heavy machinery and equipment. This bearings can support heavy radial load. The linear contact area with outer rings, helps distributing load on broader area or surface.
TYPES - N. NU, NF, NJ, NUP, N and NU  series of bearings-This are single row, cylindrical roller bearings, this are designed for axial load., NF, NJ and NUP series of bearings – This series of bearings are designed to withstand thrust load apart from radial load.
ADVANTAGES –This bearings have greater resistance to fatigue and shock then ball bearings
SPHERICAL BEARINGS – This type of bearings allow rotation around a central point in two orthogonal directions. This particular bearings are also known as ball joint bearings, can be in plan bearings or roller bearing. This bearings are in two types non sealed / open bearing and other is sealed. FUNCTION OF SPHERICAL BEARINGS- This type of bearing permits rotation with low friction and manages misalignment between the shaft and housing. This bearings are used in extreme tough running conditions. This particular bearing is used in mining, construction equipment, textile and more. KINGPIN BEARINGS –This are components in vehicle steering system, they support the vertical load and allows the steering knuckles or axles to rotate. They basically maintain the alignment and stability of the front wheels and smooth steering. The bearings are made for high quality material, which make them durable. The kingpin bearing design makes them corrosion resistance and give long life. 

IMB - BALL BEARING FOR AUTOMOTIVE AND INDUSTRIAL  USE-
OEM NUMBER  - 06 31420 0402, D10037190A. RE72126, M20129, 001082207R91, D10027190A
DIMENSIONS - 65 X 120 X 23   
The ball bearings are made of two rings or races, with steel balls in between, it helps reduces friction and allows moving parts of the machine to roll over each other. It basically reduce the friction, which increase the life of the machine or machine parts. Ball bearings are used in day to day products, like house hold electrical appliances, water pumps automotive and many other equipment’s.  Ball bearings are made up of variety of materials like Bearing steel, carbon steel, chrome steel, aluminium, tungsten carbide, platinum and many other materials.

WHAT ARE BEARINGS - Bearings are "parts that assist objects' rotation bearings assist the shaft that rotates inside the machinery smoothly.
Bearings are used in automobiles, airplanes, electric generators and so on. Also used in household appliances.The function of the Bearings is to rotating shafts of the wheels, gears, turbines, rotors, etc. in those machines, allowing them to rotate more smoothly.. The function of the bearings is to reduce friction, make rotation smoother and to protect the part that supports the rotation, and maintain the correct position for the rotating shaft.
DIFFERENT TYPES OF BEARINGS – Ball bearings, Taper, Cylindrical, Spherical, Kingpin, Needle and DAC Bearings.
WHAT ARE TAPER BEARINGS AND ITS FUNCTIONS – Tapered roller bearings supports axial forces, as well as radial forces. The taper bearings consist of Cone, Cup, Cage and Rollers.
Tapered roller bearings are made up of cone assembly and a cup. The cone assembly consists of the inner ring, the rollers, and a cage that retains and evenly spaces the rollers. The cup is simply the outer ring. Internal clearance is established during mounting by the axial position of the cone relative to the cup, although preloaded installations without clearance are common.
Cylindrical Roller Bearings – As name suggest the rollers are in cylindrical in shape. This bearings are design for heavy machinery and equipment. This bearings can support heavy radial load. The linear contact area with outer rings, helps distributing load on broader area or surface.
TYPES - N. NU, NF, NJ, NUP
N and NU  series of bearings-This are single row, cylindrical roller bearings, this are designed for axial load.
NF, NJ and NUP series of bearings – This series of bearings are designed to withstand thrust load apart from radial load.
ADVANTAGES –This bearings have greater resistance to fatigue and shock then ball bearings
SPHERICAL BEARINGS – This type of bearings allow rotation around a central point in two orthogonal directions. This particular bearings are also known as ball joint bearings, can be in plan bearings or roller bearing. This bearings are in two types non sealed / open bearing and other is sealed.
FUNCTION OF SPHERICAL BEARINGS- This type of bearing permits rotation with low friction and manages misalignment between the shaft and housing. This bearings are used in extreme tough running conditions. This particular bearing is used in mining, construction equipment, textile and more.
KINGPIN BEARINGS –This are components in vehicle steering system, they support the vertical load and allows the steering knuckles or axles to rotate. They basically maintain the alignment and stability of the front wheels and smooth steering. The bearings are made for high quality material, which make them durable. The kingpin bearing design makes them corrosion resistance and give long life. 

IMB - BALL BEARING FOR AUTOMOTIVE AND INDUSTRIAL USE.
OEM NUMBER -  06 31440 7000 / 06 31410 4300
DIMENSIONS  - 17 X 35 X 10

The ball bearings are made of two rings or races, with steel balls in between, it helps reduces friction and allows moving parts of the machine to roll over each other. It basically reduce the friction, which increase the life of the machine or machine parts. Ball bearings are used in day to day products, like house hold electrical appliances, water pumps automotive and many other equipment’s.  Ball bearings are made up of variety of materials like Bearing steel, carbon steel, chrome steel, aluminium, tungsten carbide, platinum and many other materials.

WHAT ARE BEARINGS - Bearings are "parts that assist objects' rotation bearings assist the shaft that rotates inside the machinery smoothly.
Bearings are used in automobiles, airplanes, electric generators and so on. Also used in household appliances.The function of the Bearings is to rotating shafts of the wheels, gears, turbines, rotors, etc. in those machines, allowing them to rotate more smoothly.. The function of the bearings is to reduce friction, make rotation smoother and to protect the part that supports the rotation, and maintain the correct position for the rotating shaft.
DIFFERENT TYPES OF BEARINGS – Ball bearings, Taper, Cylindrical, Spherical, Kingpin, Needle and DAC Bearings.
WHAT ARE TAPER BEARINGS AND ITS FUNCTIONS – Tapered roller bearings supports axial forces, as well as radial forces. The taper bearings consist of Cone, Cup, Cage and Rollers.
Tapered roller bearings are made up of cone assembly and a cup. The cone assembly consists of the inner ring, the rollers, and a cage that retains and evenly spaces the rollers. The cup is simply the outer ring. Internal clearance is established during mounting by the axial position of the cone relative to the cup, although preloaded installations without clearance are common.
Cylindrical Roller Bearings – As name suggest the rollers are in cylindrical in shape. This bearings are design for heavy machinery and equipment. This bearings can support heavy radial load. The linear contact area with outer rings, helps distributing load on broader area or surface.
TYPES - N. NU, NF, NJ, NUP
N and NU  series of bearings-This are single row, cylindrical roller bearings, this are designed for axial load.
NF, NJ and NUP series of bearings – This series of bearings are designed to withstand thrust load apart from radial load.
ADVANTAGES –This bearings have greater resistance to fatigue and shock then ball bearings
SPHERICAL BEARINGS – This type of bearings allow rotation around a central point in two orthogonal directions. This particular bearings are also known as ball joint bearings, can be in plan bearings or roller bearing. This bearings are in two types non sealed / open bearing and other is sealed.
FUNCTION OF SPHERICAL BEARINGS- This type of bearing permits rotation with low friction and manages misalignment between the shaft and housing. This bearings are used in extreme tough running conditions. This particular bearing is used in mining, construction equipment, textile and more.
KINGPIN BEARINGS –This are components in vehicle steering system, they support the vertical load and allows the steering knuckles or axles to rotate. They basically maintain the alignment and stability of the front wheels and smooth steering. The bearings are made for high quality material, which make them durable. The kingpin bearing design makes them corrosion resistance and give long life. This bearings are used in vehicles like Trucks, Autos, Tractors and Earthmover.

BALL BEARING FOR COMMERCIAL AND INDUSTRIAL- MAN, JOHN DEERE, CLAAS.
OEM NUMBER - RE 222978 / 0635 333 028, 31100685, 9920 11 1590, 971059
DIMENSIONS - 40 X 90 X 23 / 6308 -2RS

WHAT ARE BEARINGS - Bearings are "parts that assist objects' rotation bearings assist the shaft that rotates inside the machinery smoothly.
Bearings are used in automobiles, airplanes, electric generators and so on. Also used in household appliances.The function of the Bearings is to rotating shafts of the wheels, gears, turbines, rotors, etc. in those machines, allowing them to rotate more smoothly.. The function of the bearings is to reduce friction, make rotation smoother and to protect the part that supports the rotation, and maintain the correct position for the rotating shaft.
DIFFERENT TYPES OF BEARINGS – Ball bearings, Taper, Cylindrical, Spherical, Kingpin, Needle and DAC Bearings.
WHAT ARE TAPER BEARINGS AND ITS FUNCTIONS – Tapered roller bearings supports axial forces, as well as radial forces. The taper bearings consist of Cone, Cup, Cage and Rollers.
Tapered roller bearings are made up of cone assembly and a cup. The cone assembly consists of the inner ring, the rollers, and a cage that retains and evenly spaces the rollers. The cup is simply the outer ring. Internal clearance is established during mounting by the axial position of the cone relative to the cup, although preloaded installations without clearance are common.
Cylindrical Roller Bearings – As name suggest the rollers are in cylindrical in shape. This bearings are design for heavy machinery and equipment. This bearings can support heavy radial load. The linear contact area with outer rings, helps distributing load on broader area or surface.
TYPES - N. NU, NF, NJ, NUP
N and NU  series of bearings-This are single row, cylindrical roller bearings, this are designed for axial load.
NF, NJ and NUP series of bearings – This series of bearings are designed to withstand thrust load apart from radial load.
ADVANTAGES –This bearings have greater resistance to fatigue and shock then ball bearings
SPHERICAL BEARINGS – This type of bearings allow rotation around a central point in two orthogonal directions. This particular bearings are also known as ball joint bearings, can be in plan bearings or roller bearing. This bearings are in two types non sealed / open bearing and other is sealed.
FUNCTION OF SPHERICAL BEARINGS- This type of bearing permits rotation with low friction and manages misalignment between the shaft and housing. This bearings are used in extreme tough running conditions. This particular bearing is used in mining, construction equipment, textile and more.
KINGPIN BEARINGS –This are components in vehicle steering system, they support the vertical load and allows the steering knuckles or axles to rotate. They basically maintain the alignment and stability of the front wheels and smooth steering. The bearings are made for high quality material, which make them durable. The kingpin bearing design makes them corrosion resistance and give long life. This bearings are used in vehicles like Trucks, Autos, Tractors and Earthmover.
DAC BEARINGS- DAC bearing are Double Row Angular Contact Ball bearings, these are used in passenger cars, DAC bearing are used in automotive axles to guide rotation and load bearing parts. Normally they are available with oil seal, grease and available in ABC.

IMB ,BALL BEARING FOR COMMERCIAL VEHICLES AND INDUSRIAL USE - MAN TRUCKS
OEM NUMBER - 06 31421 4603
DIMENSIIONS - 65 X 140 X 33

The ball bearings are made of two rings or races, with steel balls in between, it helps reduces friction and allows moving parts of the machine to roll over each other. It basically reduce the friction, which increase the life of the machine or machine parts. Ball bearings are used in day to day products, like house hold electrical appliances, water pumps automotive and many other equipment’s.  Ball bearings are made up of variety of materials like Bearing steel, carbon steel, chrome steel, aluminium, tungsten carbide, platinum and many other materials.

WHAT ARE BEARINGS - Bearings are "parts that assist objects' rotation bearings assist the shaft that rotates inside the machinery smoothly.
Bearings are used in automobiles, airplanes, electric generators and so on. Also used in household appliances.The function of the Bearings is to rotating shafts of the wheels, gears, turbines, rotors, etc. in those machines, allowing them to rotate more smoothly.. The function of the bearings is to reduce friction, make rotation smoother and to protect the part that supports the rotation, and maintain the correct position for the rotating shaft.
DIFFERENT TYPES OF BEARINGS – Ball bearings, Taper, Cylindrical, Spherical, Kingpin, Needle and DAC Bearings.
WHAT ARE TAPER BEARINGS AND ITS FUNCTIONS – Tapered roller bearings supports axial forces, as well as radial forces. The taper bearings consist of Cone, Cup, Cage and Rollers.
Tapered roller bearings are made up of cone assembly and a cup. The cone assembly consists of the inner ring, the rollers, and a cage that retains and evenly spaces the rollers. The cup is simply the outer ring. Internal clearance is established during mounting by the axial position of the cone relative to the cup, although preloaded installations without clearance are common.
Cylindrical Roller Bearings – As name suggest the rollers are in cylindrical in shape. This bearings are design for heavy machinery and equipment. This bearings can support heavy radial load. The linear contact area with outer rings, helps distributing load on broader area or surface.
TYPES - N. NU, NF, NJ, NUP
N and NU  series of bearings-This are single row, cylindrical roller bearings, this are designed for axial load.
NF, NJ and NUP series of bearings – This series of bearings are designed to withstand thrust load apart from radial load.
ADVANTAGES –This bearings have greater resistance to fatigue and shock then ball bearings
SPHERICAL BEARINGS – This type of bearings allow rotation around a central point in two orthogonal directions. This particular bearings are also known as ball joint bearings, can be in plan bearings or roller bearing. This bearings are in two types non sealed / open bearing and other is sealed.
FUNCTION OF SPHERICAL BEARINGS- This type of bearing permits rotation with low friction and manages misalignment between the shaft and housing. This bearings are used in extreme tough running conditions. This particular bearing is used in mining, construction equipment, textile and more.
KINGPIN BEARINGS –This are components in vehicle steering system, they support the vertical load and allows the steering knuckles or axles to rotate. They basically maintain the alignment and stability of the front wheels and smooth steering. The bearings are made for high quality material, which make them durable. The kingpin bearing design makes them corrosion resistance and give long life. This bearings are used in vehicles like Trucks, Autos, Tractors and Earthmover.

MARAZO GEAR BOX XUV 300, COUNTER SLAFT BEARING 
6205 2RS ( 07073DH0200N)
6305 2RS (07003DD1590N)
BB12686 (SPO10101701)
F 613788  (0703DAK02741N),      IMB - ball bearings are made of two rings or races, with steel balls in between, it helps reduces friction and allows moving parts of the machine to roll over each other. It basically reduce the friction, which increase the life of the machine or machine parts. Ball bearings are used in day to day products, like house hold electrical appliances, water pumps automotive and many other equipment’s.  Ball bearings are made up of variety of materials like Bearing steel, carbon steel, chrome steel, aluminium, tungsten carbide, platinum and many other materials.WHAT ARE BEARINGS - Bearings are "parts that assist objects' rotation bearings assist the shaft that rotates inside the machinery smoothly.

Bearings are used in automobiles, airplanes, electric generators and so on. Also used in household appliances.The function of the Bearings is to rotating shafts of the wheels, gears, turbines, rotors, etc. in those machines, allowing them to rotate more smoothly.. The function of the bearings is to reduce friction, make rotation smoother and to protect the part that supports the rotation, and maintain the correct position for the rotating shaft.
DIFFERENT TYPES OF BEARINGS –IMB Ball bearings, Taper, Cylindrical, Spherical, Kingpin, Needle and DAC Bearings.Spherical roller bearings can accommodate heavy loads in both directions. They are self-aligning and accommodate misalignment and shaft deflections, with virtually no increase in friction or temperature. The design includes features to facilitate relubrication. The bearings can be used in a modular system, including housings, sleeves and nuts. Accommodate misalignment, High load carrying capacity, Relubrication features, Low friction and long service life, Increased wear resistance

WHAT ARE TAPER BEARINGS AND ITS FUNCTIONS – Tapered roller bearings supports axial forces, as well as radial forces. The taper bearings consist of Cone, Cup, Cage and Rollers.
Tapered roller bearings are made up of cone assembly and a cup. The cone assembly consists of the inner ring, the rollers, and a cage that retains and evenly spaces the rollers. The cup is simply the outer ring. Internal clearance is established during mounting by the axial position of the cone relative to the cup, although preloaded installations without clearance are common.
IMB -Cylindrical Roller Bearings – As name suggest the rollers are in cylindrical in shape. This bearings are design for heavy machinery and equipment. This bearings can support heavy radial load. The linear contact area with outer rings, helps distributing load on broader area or surface.
IMB - TYPES - N. NU, NF, NJ, NUP
N and NU  series of bearings-This are single row, cylindrical roller bearings, this are designed for axial load.
NF, NJ and NUP series of bearings – This series of bearings are designed to withstand thrust load apart from radial load.
ADVANTAGES –This bearings have greater resistance to fatigue and shock then ball bearings
IMB - SPHERICAL BEARINGS – This type of bearings allow rotation around a central point in two orthogonal directions. This particular bearings are also known as ball joint bearings, can be in plan bearings or roller bearing. This bearings are in two types non sealed / open bearing and other is sealed.
FUNCTION OF SPHERICAL BEARINGS- This type of bearing permits rotation with low friction and manages misalignment between the shaft and housing. This bearings are used in extreme tough running conditions. This particular bearing is used in mining, construction equipment. 

IMB BEARINGS FOR, FORK LIFT BEARINGS MAST BEARINGS VOLTAS FORK LIFT, GODREJ FORK LIFT, ACE FORK LIFT ,TOYOTA FORK LIFT

BORE DIAMETER = 55
OUTER DIAMETER = 152
WIDTH = 45,   IMB BEARING,   Forklift roller bearings, or mast guide bearings, are designed to carry heavy loads and withstand high intermittent shock loads. Forklift bearings internal design maximizes load and protects the bearing component. This bearings have tight seals and high grease filling for minimal wear and tear


WHAT ARE BEARINGS - Bearings are "parts that assist objects' rotation bearings assist the shaft that rotates inside the machinery smoothly.Bearings are used in automobiles, airplanes, electric generators and so on. Also used in household appliances.The function of the Bearings is to rotating shafts of the wheels, gears, turbines, rotors, etc. in those machines, allowing them to rotate more smoothly.. The function of the bearings is to reduce friction, make rotation smoother and to protect the part that supports the rotation, and maintain the correct position for the rotating shaft. DIFFERENT TYPES OF BEARINGS –IMB-  Ball bearings, Taper, Cylindrical, Spherical, Kingpin, Needle and DAC Bearings.WHAT ARE TAPER BEARINGS AND ITS FUNCTIONS – Tapered roller bearings supports axial forces, as well as radial forces. The taper bearings consist of Cone, Cup, Cage and Rollers. Tapered roller bearings are made up of cone assembly and a cup. The cone assembly consists of the inner ring, the rollers, and a cage that retains and evenly spaces the rollers. The cup is simply the outer ring. Internal clearance is established during mounting by the axial position of the cone relative to the cup, although preloaded installations without clearance are common.IMB Cylindrical Roller Bearings – As name suggest the rollers are in cylindrical in shape. This bearings are design for heavy machinery and equipment. This bearings can support heavy radial load. The linear contact area with outer rings, helps distributing load on broader area or surface.Hub units – Also known as wheel bearing hubs, are critical part of the vehicle suspension system that allow the wheel to rotate smoothly and also support the vehicle’s weight. Available in as insert repair unit and repair unit. Hub unit contain two taper roller bearings, are pre-adjusted, greased and sealed at the factory in order to simplify installation. Truck Hub Units are double-row tapered roller bearings with separate cones held together by a retention ring and assembled in a one-piece outer ring.IMB - DAC BEARINGS- DAC bearing are Double Row Angular Contact Ball bearings, these are used in passenger cars, DAC bearing are used in automotive axles to guide rotation and load bearing parts. Normally they are available with oil seal, grease and available in ABC.

IMB - BALL BEARINGS FOR AUTOMOTIVE AND INDUSTRIAL USE.
OEM NUMBER - 06 31450 4300
DIMENSIONS - 10 X 30 X 9
HINDUSTAN MOTORS- 81008932

The ball bearings are made of two rings or races, with steel balls in between, it helps reduces friction and allows moving parts of the machine to roll over each other. It basically reduce the friction, which increase the life of the machine or machine parts. Ball bearings are used in day to day products, like house hold electrical appliances, water pumps automotive and many other equipment’s.  Ball bearings are made up of variety of materials like Bearing steel, carbon steel, chrome steel, aluminium, tungsten carbide, platinum and many other materials.

WHAT ARE BEARINGS - Bearings are "parts that assist objects' rotation bearings assist the shaft that rotates inside the machinery smoothly.
Bearings are used in automobiles, airplanes, electric generators and so on. Also used in household appliances.The function of the Bearings is to rotating shafts of the wheels, gears, turbines, rotors, etc. in those machines, allowing them to rotate more smoothly.. The function of the bearings is to reduce friction, make rotation smoother and to protect the part that supports the rotation, and maintain the correct position for the rotating shaft.
DIFFERENT TYPES OF BEARINGS – Ball bearings, Taper, Cylindrical, Spherical, Kingpin, Needle and DAC Bearings.
WHAT ARE TAPER BEARINGS AND ITS FUNCTIONS – Tapered roller bearings supports axial forces, as well as radial forces. The taper bearings consist of Cone, Cup, Cage and Rollers.
Tapered roller bearings are made up of cone assembly and a cup. The cone assembly consists of the inner ring, the rollers, and a cage that retains and evenly spaces the rollers. The cup is simply the outer ring. Internal clearance is established during mounting by the axial position of the cone relative to the cup, although preloaded installations without clearance are common.
Cylindrical Roller Bearings – As name suggest the rollers are in cylindrical in shape. This bearings are design for heavy machinery and equipment. This bearings can support heavy radial load. The linear contact area with outer rings, helps distributing load on broader area or surface.
TYPES - N. NU, NF, NJ, NUP
N and NU  series of bearings-This are single row, cylindrical roller bearings, this are designed for axial load.
NF, NJ and NUP series of bearings – This series of bearings are designed to withstand thrust load apart from radial load.
ADVANTAGES –This bearings have greater resistance to fatigue and shock then ball bearings
SPHERICAL BEARINGS – This type of bearings allow rotation around a central point in two orthogonal directions. This particular bearings are also known as ball joint bearings, can be in plan bearings or roller bearing. This bearings are in two types non sealed / open bearing and other is sealed.
FUNCTION OF SPHERICAL BEARINGS- This type of bearing permits rotation with low friction and manages misalignment between the shaft and housing. This bearings are used in extreme tough running conditions. This particular bearing is used in mining, construction equipment, textile and more.
KINGPIN BEARINGS –This are components in vehicle steering system, they support the vertical load and allows the steering knuckles or axles to rotate. They basically maintain the alignment and stability of the front wheels and smooth steering. The bearings are made for high quality material, which make them durable. The kingpin bearing design makes them corrosion resistance and give long life. This bearings are used in vehicles like Trucks, Autos, Tractors and Earthmover.

IMB BEARINGS FOR- FORK LIFT BEARINGS MAST BEARINGS VOLTAS FORK LIFT, GODREJ FORK LIFT, ACE FORK LIFT ,TOYOTA FORK LIFT
BORE DIAMETER = 55
OUTER DIAMETER = 96
WIDTH = 33,   IMB BEARINGS,   Forklift roller bearings, or mast guide bearings, are designed to carry heavy loads and withstand high intermittent shock loads. Forklift bearings internal design maximizes load and protects the bearing component. This bearings have tight seals and high grease filling for minimal wear and tear


WHAT ARE BEARINGS - Bearings are "parts that assist objects' rotation bearings assist the shaft that rotates inside the machinery smoothly.Bearings are used in automobiles, airplanes, electric generators and so on. Also used in household appliances.The function of the Bearings is to rotating shafts of the wheels, gears, turbines, rotors, etc. in those machines, allowing them to rotate more smoothly.. The function of the bearings is to reduce friction, make rotation smoother and to protect the part that supports the rotation, and maintain the correct position for the rotating shaft. DIFFERENT TYPES OF BEARINGS –IMB-  Ball bearings, Taper, Cylindrical, Spherical, Kingpin, Needle and DAC Bearings.WHAT ARE TAPER BEARINGS AND ITS FUNCTIONS – Tapered roller bearings supports axial forces, as well as radial forces. The taper bearings consist of Cone, Cup, Cage and Rollers. Tapered roller bearings are made up of cone assembly and a cup. The cone assembly consists of the inner ring, the rollers, and a cage that retains and evenly spaces the rollers. The cup is simply the outer ring. Internal clearance is established during mounting by the axial position of the cone relative to the cup, although preloaded installations without clearance are common.IMB Cylindrical Roller Bearings – As name suggest the rollers are in cylindrical in shape. This bearings are design for heavy machinery and equipment. This bearings can support heavy radial load. The linear contact area with outer rings, helps distributing load on broader area or surface.Hub units – Also known as wheel bearing hubs, are critical part of the vehicle suspension system that allow the wheel to rotate smoothly and also support the vehicle’s weight. Available in as insert repair unit and repair unit. Hub unit contain two taper roller bearings, are pre-adjusted, greased and sealed at the factory in order to simplify installation. Truck Hub Units are double-row tapered roller bearings with separate cones held together by a retention ring and assembled in a one-piece outer ring.IMB - DAC BEARINGS- DAC bearing are Double Row Angular Contact Ball bearings, these are used in passenger cars, DAC bearing are used in automotive axles to guide rotation and load bearing parts. Normally they are available with oil seal, grease and available in ABC.

IMB BEARINGS FOR- FORK LIFT BEARINGS MAST BEARINGS VOLTAS FORK LIFT, GODREJ FORK LIFT, ACE FORK LIFT ,TOYOTA FORK LIFT
BORE DIAMETER = 55
OUTER DIAMETER = 121
WIDTH = 34,   IMB BEARIN GS,  Forklift roller bearings, or mast guide bearings, are designed to carry heavy loads and withstand high intermittent shock loads. Forklift bearings internal design maximizes load and protects the bearing component. This bearings have tight seals and high grease filling for minimal wear and tear


WHAT ARE BEARINGS - Bearings are "parts that assist objects' rotation bearings assist the shaft that rotates inside the machinery smoothly.Bearings are used in automobiles, airplanes, electric generators and so on. Also used in household appliances.The function of the Bearings is to rotating shafts of the wheels, gears, turbines, rotors, etc. in those machines, allowing them to rotate more smoothly.. The function of the bearings is to reduce friction, make rotation smoother and to protect the part that supports the rotation, and maintain the correct position for the rotating shaft. DIFFERENT TYPES OF BEARINGS –IMB-  Ball bearings, Taper, Cylindrical, Spherical, Kingpin, Needle and DAC Bearings.WHAT ARE TAPER BEARINGS AND ITS FUNCTIONS – Tapered roller bearings supports axial forces, as well as radial forces. The taper bearings consist of Cone, Cup, Cage and Rollers. Tapered roller bearings are made up of cone assembly and a cup. The cone assembly consists of the inner ring, the rollers, and a cage that retains and evenly spaces the rollers. The cup is simply the outer ring. Internal clearance is established during mounting by the axial position of the cone relative to the cup, although preloaded installations without clearance are common.IMB Cylindrical Roller Bearings – As name suggest the rollers are in cylindrical in shape. This bearings are design for heavy machinery and equipment. This bearings can support heavy radial load. The linear contact area with outer rings, helps distributing load on broader area or surface.Hub units – Also known as wheel bearing hubs, are critical part of the vehicle suspension system that allow the wheel to rotate smoothly and also support the vehicle’s weight. Available in as insert repair unit and repair unit. Hub unit contain two taper roller bearings, are pre-adjusted, greased and sealed at the factory in order to simplify installation. Truck Hub Units are double-row tapered roller bearings with separate cones held together by a retention ring and assembled in a one-piece outer ring.IMB - DAC BEARINGS- DAC bearing are Double Row Angular Contact Ball bearings, these are used in passenger cars, DAC bearing are used in automotive axles to guide rotation and load bearing parts. Normally they are available with oil seal, grease and available in ABC.

IMB BEARINGS FOR- FORK LIFT BEARINGS MAST BEARINGS VOLTAS FORK LIFT, GODREJ FORK LIFT, ACE FORK LIFT ,TOYOTA FORK LIFT

BORE DIAMETER = 45
OUTER DIAMETER = 125
WIDTH = 32,   
IMB BEARINGS ,   Forklift roller bearings, or mast guide bearings, are designed to carry heavy loads and withstand high intermittent shock loads. Forklift bearings internal design maximizes load and protects the bearing component. This bearings have tight seals and high grease filling for minimal wear and tear


WHAT ARE BEARINGS - Bearings are "parts that assist objects' rotation bearings assist the shaft that rotates inside the machinery smoothly.Bearings are used in automobiles, airplanes, electric generators and so on. Also used in household appliances.The function of the Bearings is to rotating shafts of the wheels, gears, turbines, rotors, etc. in those machines, allowing them to rotate more smoothly.. The function of the bearings is to reduce friction, make rotation smoother and to protect the part that supports the rotation, and maintain the correct position for the rotating shaft. DIFFERENT TYPES OF BEARINGS –IMB-  Ball bearings, Taper, Cylindrical, Spherical, Kingpin, Needle and DAC Bearings.WHAT ARE TAPER BEARINGS AND ITS FUNCTIONS – Tapered roller bearings supports axial forces, as well as radial forces. The taper bearings consist of Cone, Cup, Cage and Rollers. Tapered roller bearings are made up of cone assembly and a cup. The cone assembly consists of the inner ring, the rollers, and a cage that retains and evenly spaces the rollers. The cup is simply the outer ring. Internal clearance is established during mounting by the axial position of the cone relative to the cup, although preloaded installations without clearance are common.IMB Cylindrical Roller Bearings – As name suggest the rollers are in cylindrical in shape. This bearings are design for heavy machinery and equipment. This bearings can support heavy radial load. The linear contact area with outer rings, helps distributing load on broader area or surface.Hub units – Also known as wheel bearing hubs, are critical part of the vehicle suspension system that allow the wheel to rotate smoothly and also support the vehicle’s weight. Available in as insert repair unit and repair unit. Hub unit contain two taper roller bearings, are pre-adjusted, greased and sealed at the factory in order to simplify installation. Truck Hub Units are double-row tapered roller bearings with separate cones held together by a retention ring and assembled in a one-piece outer ring.IMB - DAC BEARINGS- DAC bearing are Double Row Angular Contact Ball bearings, these are used in passenger cars, DAC bearing are used in automotive axles to guide rotation and load bearing parts. Normally they are available with oil seal, grease and available in ABC.

IMB BEARINGS FOR , FORK LIFT BEARINGS MAST BEARINGS VOLTAS FORK LIFT, GODREJ FORK LIFT, ACE FORK LIFT ,TOYOTA FORK LIFT

BORE DIAMETER = 55
OUTER DIAMETER = 113.5
WIDTH = 35,   IMB BEARINGS,   Forklift roller bearings, or mast guide bearings, are designed to carry heavy loads and withstand high intermittent shock loads. Forklift bearings internal design maximizes load and protects the bearing component. This bearings have tight seals and high grease filling for minimal wear and tear


WHAT ARE BEARINGS - Bearings are "parts that assist objects' rotation bearings assist the shaft that rotates inside the machinery smoothly.Bearings are used in automobiles, airplanes, electric generators and so on. Also used in household appliances.The function of the Bearings is to rotating shafts of the wheels, gears, turbines, rotors, etc. in those machines, allowing them to rotate more smoothly.. The function of the bearings is to reduce friction, make rotation smoother and to protect the part that supports the rotation, and maintain the correct position for the rotating shaft. DIFFERENT TYPES OF BEARINGS –IMB-  Ball bearings, Taper, Cylindrical, Spherical, Kingpin, Needle and DAC Bearings.WHAT ARE TAPER BEARINGS AND ITS FUNCTIONS – Tapered roller bearings supports axial forces, as well as radial forces. The taper bearings consist of Cone, Cup, Cage and Rollers. Tapered roller bearings are made up of cone assembly and a cup. The cone assembly consists of the inner ring, the rollers, and a cage that retains and evenly spaces the rollers. The cup is simply the outer ring. Internal clearance is established during mounting by the axial position of the cone relative to the cup, although preloaded installations without clearance are common.IMB Cylindrical Roller Bearings – As name suggest the rollers are in cylindrical in shape. This bearings are design for heavy machinery and equipment. This bearings can support heavy radial load. The linear contact area with outer rings, helps distributing load on broader area or surface.Hub units – Also known as wheel bearing hubs, are critical part of the vehicle suspension system that allow the wheel to rotate smoothly and also support the vehicle’s weight. Available in as insert repair unit and repair unit. Hub unit contain two taper roller bearings, are pre-adjusted, greased and sealed at the factory in order to simplify installation. Truck Hub Units are double-row tapered roller bearings with separate cones held together by a retention ring and assembled in a one-piece outer ring.IMB - DAC BEARINGS- DAC bearing are Double Row Angular Contact Ball bearings, these are used in passenger cars, DAC bearing are used in automotive axles to guide rotation and load bearing parts. Normally they are available with oil seal, grease and available in ABC.

IMB BEARING FOR, FORK LIFT BEARINGS MAST BEARINGS VOLTAS FORK LIFT, GODREJ FORK LIFT, ACE FORK LIFT ,TOYOTA FORK LIFT.
DIMENSION.
ID:40
OD:90
WEIDTH:29,   IMB BEARING -  Forklift roller bearings, or mast guide bearings, are designed to carry heavy loads and withstand high intermittent shock loads. Forklift bearings internal design maximizes load and protects the bearing component. This bearings have tight seals and high grease filling for minimal wear and tear


WHAT ARE BEARINGS - Bearings are "parts that assist objects' rotation bearings assist the shaft that rotates inside the machinery smoothly.Bearings are used in automobiles, airplanes, electric generators and so on. Also used in household appliances.The function of the Bearings is to rotating shafts of the wheels, gears, turbines, rotors, etc. in those machines, allowing them to rotate more smoothly.. The function of the bearings is to reduce friction, make rotation smoother and to protect the part that supports the rotation, and maintain the correct position for the rotating shaft. DIFFERENT TYPES OF BEARINGS –IMB-  Ball bearings, Taper, Cylindrical, Spherical, Kingpin, Needle and DAC Bearings.WHAT ARE TAPER BEARINGS AND ITS FUNCTIONS – Tapered roller bearings supports axial forces, as well as radial forces. The taper bearings consist of Cone, Cup, Cage and Rollers. Tapered roller bearings are made up of cone assembly and a cup. The cone assembly consists of the inner ring, the rollers, and a cage that retains and evenly spaces the rollers. The cup is simply the outer ring. Internal clearance is established during mounting by the axial position of the cone relative to the cup, although preloaded installations without clearance are common.IMB Cylindrical Roller Bearings – As name suggest the rollers are in cylindrical in shape. This bearings are design for heavy machinery and equipment. This bearings can support heavy radial load. The linear contact area with outer rings, helps distributing load on broader area or surface.Hub units – Also known as wheel bearing hubs, are critical part of the vehicle suspension system that allow the wheel to rotate smoothly and also support the vehicle’s weight. Available in as insert repair unit and repair unit. Hub unit contain two taper roller bearings, are pre-adjusted, greased and sealed at the factory in order to simplify installation. Truck Hub Units are double-row tapered roller bearings with separate cones held together by a retention ring and assembled in a one-piece outer ring.IMB - DAC BEARINGS- DAC bearing are Double Row Angular Contact Ball bearings, these are used in passenger cars, DAC bearing are used in automotive axles to guide rotation and load bearing parts. Normally they are available with oil seal, grease and available in ABC.

imb bearing for, FORK LIFT BEARINGS MAST BEARINGS VOLTAS FORK LIFT, GODREJ FORK LIFT, ACE FORK LIFT ,TOYOTA FORK LIFT.
DIMENSION.
ID:35
OD:88
WEIDTH:31,   
imb bearings.  Forklift roller bearings, or mast guide bearings, are designed to carry heavy loads and withstand high intermittent shock loads. Forklift bearings internal design maximizes load and protects the bearing component. This bearings have tight seals and high grease filling for minimal wear and tear


WHAT ARE BEARINGS - Bearings are "parts that assist objects' rotation bearings assist the shaft that rotates inside the machinery smoothly.Bearings are used in automobiles, airplanes, electric generators and so on. Also used in household appliances.The function of the Bearings is to rotating shafts of the wheels, gears, turbines, rotors, etc. in those machines, allowing them to rotate more smoothly.. The function of the bearings is to reduce friction, make rotation smoother and to protect the part that supports the rotation, and maintain the correct position for the rotating shaft. DIFFERENT TYPES OF BEARINGS –IMB-  Ball bearings, Taper, Cylindrical, Spherical, Kingpin, Needle and DAC Bearings.WHAT ARE TAPER BEARINGS AND ITS FUNCTIONS – Tapered roller bearings supports axial forces, as well as radial forces. The taper bearings consist of Cone, Cup, Cage and Rollers. Tapered roller bearings are made up of cone assembly and a cup. The cone assembly consists of the inner ring, the rollers, and a cage that retains and evenly spaces the rollers. The cup is simply the outer ring. Internal clearance is established during mounting by the axial position of the cone relative to the cup, although preloaded installations without clearance are common.IMB Cylindrical Roller Bearings – As name suggest the rollers are in cylindrical in shape. This bearings are design for heavy machinery and equipment. This bearings can support heavy radial load. The linear contact area with outer rings, helps distributing load on broader area or surface.Hub units – Also known as wheel bearing hubs, are critical part of the vehicle suspension system that allow the wheel to rotate smoothly and also support the vehicle’s weight. Available in as insert repair unit and repair unit. Hub unit contain two taper roller bearings, are pre-adjusted, greased and sealed at the factory in order to simplify installation. Truck Hub Units are double-row tapered roller bearings with separate cones held together by a retention ring and assembled in a one-piece outer ring.IMB - DAC BEARINGS- DAC bearing are Double Row Angular Contact Ball bearings, these are used in passenger cars, DAC bearing are used in automotive axles to guide rotation and load bearing parts. Normally they are available with oil seal, grease and available in ABC.

IMB BEARINGS FOR FORK LIFT BEARINGS MAST BEARINGS VOLTAS FORK LIFT, GODREJ FORK LIFT, ACE FORK LIFT ,TOYOTA FORK LIFT

BORE DIAMETER (MM) = 40 (MM) 

OUTER DIAMETER (MM) = 105.8

WIDTH = 22

 

WHAT ARE BEARINGS - Bearings are "parts that assist objects' rotation bearings assist the shaft that rotates inside the machinery smoothly.
Bearings are used in automobiles, airplanes, electric generators and so on. Also used in household appliances.The function of the Bearings is to rotating shafts of the wheels, gears, turbines, rotors, etc. in those machines, allowing them to rotate more smoothly.. The function of the bearings is to reduce friction, make rotation smoother and to protect the part that supports the rotation, and maintain the correct position for the rotating shaft.
DIFFERENT TYPES OF BEARINGS –IMB-  Ball bearings, Taper, Cylindrical, Spherical, Kingpin, Needle and DAC Bearings.
WHAT ARE TAPER BEARINGS AND ITS FUNCTIONS – Tapered roller bearings supports axial forces, as well as radial forces. The taper bearings consist of Cone, Cup, Cage and Rollers.
Tapered roller bearings are made up of cone assembly and a cup. The cone assembly consists of the inner ring, the rollers, and a cage that retains and evenly spaces the rollers. The cup is simply the outer ring. Internal clearance is established during mounting by the axial position of the cone relative to the cup, although preloaded installations without clearance are common.
IMB Cylindrical Roller Bearings – As name suggest the rollers are in cylindrical in shape. This bearings are design for heavy machinery and equipment. This bearings can support heavy radial load. The linear contact area with outer rings, helps distributing load on broader area or surface.
Hub units – Also known as wheel bearing hubs, are critical part of the vehicle suspension system that allow the wheel to rotate smoothly and also support the vehicle’s weight. Available in as insert repair unit and repair unit. Hub unit contain two taper roller bearings, are pre-adjusted, greased and sealed at the factory in order to simplify installation. Truck Hub Units are double-row tapered roller bearings with separate cones held together by a retention ring and assembled in a one-piece outer ring.

IMB - DAC BEARINGS- DAC bearing are Double Row Angular Contact Ball bearings, these are used in passenger cars, DAC bearing are used in automotive axles to guide rotation and load bearing parts. Normally they are available with oil seal, grease and available in ABC.

IMB BEARING FOR , FORK LIFT BEARINGS MAST BEARINGS VOLTAS FORK LIFT, GODREJ FORK LIFT, ACE FORK LIFT ,TOYOTA FORK LIFT

BORE DIAMETER = 55
OUTER DIAMETER = 152
WIDTH = 38,   
IMB BEARING-  Forklift roller bearings, or mast guide bearings, are designed to carry heavy loads and withstand high intermittent shock loads. Forklift bearings internal design maximizes load and protects the bearing component. This bearings have tight seals and high grease filling for minimal wear and tear


WHAT ARE BEARINGS - Bearings are "parts that assist objects' rotation bearings assist the shaft that rotates inside the machinery smoothly.Bearings are used in automobiles, airplanes, electric generators and so on. Also used in household appliances.The function of the Bearings is to rotating shafts of the wheels, gears, turbines, rotors, etc. in those machines, allowing them to rotate more smoothly.. The function of the bearings is to reduce friction, make rotation smoother and to protect the part that supports the rotation, and maintain the correct position for the rotating shaft. DIFFERENT TYPES OF BEARINGS –IMB-  Ball bearings, Taper, Cylindrical, Spherical, Kingpin, Needle and DAC Bearings.WHAT ARE TAPER BEARINGS AND ITS FUNCTIONS – Tapered roller bearings supports axial forces, as well as radial forces. The taper bearings consist of Cone, Cup, Cage and Rollers. Tapered roller bearings are made up of cone assembly and a cup. The cone assembly consists of the inner ring, the rollers, and a cage that retains and evenly spaces the rollers. The cup is simply the outer ring. Internal clearance is established during mounting by the axial position of the cone relative to the cup, although preloaded installations without clearance are common.IMB Cylindrical Roller Bearings – As name suggest the rollers are in cylindrical in shape. This bearings are design for heavy machinery and equipment. This bearings can support heavy radial load. The linear contact area with outer rings, helps distributing load on broader area or surface.Hub units – Also known as wheel bearing hubs, are critical part of the vehicle suspension system that allow the wheel to rotate smoothly and also support the vehicle’s weight. Available in as insert repair unit and repair unit. Hub unit contain two taper roller bearings, are pre-adjusted, greased and sealed at the factory in order to simplify installation. Truck Hub Units are double-row tapered roller bearings with separate cones held together by a retention ring and assembled in a one-piece outer ring.IMB - DAC BEARINGS- DAC bearing are Double Row Angular Contact Ball bearings, these are used in passenger cars, DAC bearing are used in automotive axles to guide rotation and load bearing parts. Normally they are available with oil seal, grease and available in ABC.

IMB BEARING FOR- FORK LIFT BEARINGS MAST BEARINGS VOLTAS FORK LIFT, GODREJ FORK LIFT, ACE FORK LIFT ,TOYOTA FORK LIFT
BORE DIAMETER = 50
OUTER DIAMETER = 102
WIDTH = 35,   
IMB BEARINGS ,  Forklift roller bearings, or mast guide bearings, are designed to carry heavy loads and withstand high intermittent shock loads. Forklift bearings internal design maximizes load and protects the bearing component. This bearings have tight seals and high grease filling for minimal wear and tear


WHAT ARE BEARINGS - Bearings are "parts that assist objects' rotation bearings assist the shaft that rotates inside the machinery smoothly.Bearings are used in automobiles, airplanes, electric generators and so on. Also used in household appliances.The function of the Bearings is to rotating shafts of the wheels, gears, turbines, rotors, etc. in those machines, allowing them to rotate more smoothly.. The function of the bearings is to reduce friction, make rotation smoother and to protect the part that supports the rotation, and maintain the correct position for the rotating shaft. DIFFERENT TYPES OF BEARINGS –IMB-  Ball bearings, Taper, Cylindrical, Spherical, Kingpin, Needle and DAC Bearings.WHAT ARE TAPER BEARINGS AND ITS FUNCTIONS – Tapered roller bearings supports axial forces, as well as radial forces. The taper bearings consist of Cone, Cup, Cage and Rollers. Tapered roller bearings are made up of cone assembly and a cup. The cone assembly consists of the inner ring, the rollers, and a cage that retains and evenly spaces the rollers. The cup is simply the outer ring. Internal clearance is established during mounting by the axial position of the cone relative to the cup, although preloaded installations without clearance are common.IMB Cylindrical Roller Bearings – As name suggest the rollers are in cylindrical in shape. This bearings are design for heavy machinery and equipment. This bearings can support heavy radial load. The linear contact area with outer rings, helps distributing load on broader area or surface.Hub units – Also known as wheel bearing hubs, are critical part of the vehicle suspension system that allow the wheel to rotate smoothly and also support the vehicle’s weight. Available in as insert repair unit and repair unit. Hub unit contain two taper roller bearings, are pre-adjusted, greased and sealed at the factory in order to simplify installation. Truck Hub Units are double-row tapered roller bearings with separate cones held together by a retention ring and assembled in a one-piece outer ring.IMB - DAC BEARINGS- DAC bearing are Double Row Angular Contact Ball bearings, these are used in passenger cars, DAC bearing are used in automotive axles to guide rotation and load bearing parts. Normally they are available with oil seal, grease and available in ABC.

IMB BERINGS FOR-FORK LIFT BEARINGS MAST BEARINGS VOLTAS FORK LIFT, GODREJ FORK LIFT, ACE FORK LIFT ,TOYOTA FORK LIFT.
DIMENSION:
ID:40
OD:102
WIDTH:25.5,  IMB BEARING,  Forklift roller bearings, or mast guide bearings, are designed to carry heavy loads and withstand high intermittent shock loads. Forklift bearings internal design maximizes load and protects the bearing component. This bearings have tight seals and high grease filling for minimal wear and tear


WHAT ARE BEARINGS - Bearings are "parts that assist objects' rotation bearings assist the shaft that rotates inside the machinery smoothly.Bearings are used in automobiles, airplanes, electric generators and so on. Also used in household appliances.The function of the Bearings is to rotating shafts of the wheels, gears, turbines, rotors, etc. in those machines, allowing them to rotate more smoothly.. The function of the bearings is to reduce friction, make rotation smoother and to protect the part that supports the rotation, and maintain the correct position for the rotating shaft. DIFFERENT TYPES OF BEARINGS –IMB-  Ball bearings, Taper, Cylindrical, Spherical, Kingpin, Needle and DAC Bearings.WHAT ARE TAPER BEARINGS AND ITS FUNCTIONS – Tapered roller bearings supports axial forces, as well as radial forces. The taper bearings consist of Cone, Cup, Cage and Rollers. Tapered roller bearings are made up of cone assembly and a cup. The cone assembly consists of the inner ring, the rollers, and a cage that retains and evenly spaces the rollers. The cup is simply the outer ring. Internal clearance is established during mounting by the axial position of the cone relative to the cup, although preloaded installations without clearance are common.IMB Cylindrical Roller Bearings – As name suggest the rollers are in cylindrical in shape. This bearings are design for heavy machinery and equipment. This bearings can support heavy radial load. The linear contact area with outer rings, helps distributing load on broader area or surface.Hub units – Also known as wheel bearing hubs, are critical part of the vehicle suspension system that allow the wheel to rotate smoothly and also support the vehicle’s weight. Available in as insert repair unit and repair unit. Hub unit contain two taper roller bearings, are pre-adjusted, greased and sealed at the factory in order to simplify installation. Truck Hub Units are double-row tapered roller bearings with separate cones held together by a retention ring and assembled in a one-piece outer ring.IMB - DAC BEARINGS- DAC bearing are Double Row Angular Contact Ball bearings, these are used in passenger cars, DAC bearing are used in automotive axles to guide rotation and load bearing parts. Normally they are available with oil seal, grease and available in ABC.

fork lift bearings mast bearings voltas fork lift, godrej fork lift, ace fork lift ,toyota fork lift
bore diamter = 40
outer diameter = 120
width = 28

WHAT ARE BEARINGS - Bearings are "parts that assist objects' rotation bearings assist the shaft that rotates inside the machinery smoothly.
Bearings are used in automobiles, airplanes, electric generators and so on. Also used in household appliances.The function of the Bearings is to rotating shafts of the wheels, gears, turbines, rotors, etc. in those machines, allowing them to rotate more smoothly.. The function of the bearings is to reduce friction, make rotation smoother and to protect the part that supports the rotation, and maintain the correct position for the rotating shaft.
DIFFERENT TYPES OF BEARINGS –IMB-  Ball bearings, Taper, Cylindrical, Spherical, Kingpin, Needle and DAC Bearings.
WHAT ARE TAPER BEARINGS AND ITS FUNCTIONS – Tapered roller bearings supports axial forces, as well as radial forces. The taper bearings consist of Cone, Cup, Cage and Rollers.
Tapered roller bearings are made up of cone assembly and a cup. The cone assembly consists of the inner ring, the rollers, and a cage that retains and evenly spaces the rollers. The cup is simply the outer ring. Internal clearance is established during mounting by the axial position of the cone relative to the cup, although preloaded installations without clearance are common.
IMB Cylindrical Roller Bearings – As name suggest the rollers are in cylindrical in shape. This bearings are design for heavy machinery and equipment. This bearings can support heavy radial load. The linear contact area with outer rings, helps distributing load on broader area or surface.
Hub units – Also known as wheel bearing hubs, are critical part of the vehicle suspension system that allow the wheel to rotate smoothly and also support the vehicle’s weight. Available in as insert repair unit and repair unit. Hub unit contain two taper roller bearings, are pre-adjusted, greased and sealed at the factory in order to simplify installation. Truck Hub Units are double-row tapered roller bearings with separate cones held together by a retention ring and assembled in a one-piece outer ring.

IMB - DAC BEARINGS- DAC bearing are Double Row Angular Contact Ball bearings, these are used in passenger cars, DAC bearing are used in automotive axles to guide rotation and load bearing parts. Normally they are available with oil seal, grease and available in ABC.

IMB - timing tensioner bearing FOR cars. These are belt-driven system that provides tension to the timing belt. The function is to provides pressure to timing belt, which drives other pulleys, helps reducing the strain on the belt. Supports the mechanical rotating body

A timing tensioner bearing has several functions, including: 

·         Pressure: Provides pressure to the timing belt, which drives other pulleys 

·         Strain relief: Eases the strain on the belt 

·         Constant tension: Ensures that the alternator has enough power to move the pulleys 

·         Support: Supports the mechanical rotating body 

·         Friction reduction: Reduces the friction coefficient during its movement 

 

 

IMB BEARINGS FOR - FORK LIFT BEARINGS MAST BEARINGS VOLTAS FORK LIFT, GODREJ FORK LIFT, ACE FORK LIFT ,TOYOTA FORK LIFT
DIMENSION- 40X102X28,    
IMB BEARINGS,  Forklift roller bearings, or mast guide bearings, are designed to carry heavy loads and withstand high intermittent shock loads. Forklift bearings internal design maximizes load and protects the bearing component. This bearings have tight seals and high grease filling for minimal wear and tear


WHAT ARE BEARINGS - Bearings are "parts that assist objects' rotation bearings assist the shaft that rotates inside the machinery smoothly.Bearings are used in automobiles, airplanes, electric generators and so on. Also used in household appliances.The function of the Bearings is to rotating shafts of the wheels, gears, turbines, rotors, etc. in those machines, allowing them to rotate more smoothly.. The function of the bearings is to reduce friction, make rotation smoother and to protect the part that supports the rotation, and maintain the correct position for the rotating shaft. DIFFERENT TYPES OF BEARINGS –IMB-  Ball bearings, Taper, Cylindrical, Spherical, Kingpin, Needle and DAC Bearings.WHAT ARE TAPER BEARINGS AND ITS FUNCTIONS – Tapered roller bearings supports axial forces, as well as radial forces. The taper bearings consist of Cone, Cup, Cage and Rollers. Tapered roller bearings are made up of cone assembly and a cup. The cone assembly consists of the inner ring, the rollers, and a cage that retains and evenly spaces the rollers. The cup is simply the outer ring. Internal clearance is established during mounting by the axial position of the cone relative to the cup, although preloaded installations without clearance are common.IMB Cylindrical Roller Bearings – As name suggest the rollers are in cylindrical in shape. This bearings are design for heavy machinery and equipment. This bearings can support heavy radial load. The linear contact area with outer rings, helps distributing load on broader area or surface.Hub units – Also known as wheel bearing hubs, are critical part of the vehicle suspension system that allow the wheel to rotate smoothly and also support the vehicle’s weight. Available in as insert repair unit and repair unit. Hub unit contain two taper roller bearings, are pre-adjusted, greased and sealed at the factory in order to simplify installation. Truck Hub Units are double-row tapered roller bearings with separate cones held together by a retention ring and assembled in a one-piece outer ring.IMB - DAC BEARINGS- DAC bearing are Double Row Angular Contact Ball bearings, these are used in passenger cars, DAC bearing are used in automotive axles to guide rotation and load bearing parts. Normally they are available with oil seal, grease and available in ABC.

IMB BEARING FOR-FORK LIFT BEARINGS MAST BEARINGS VOLTAS FORK LIFT, GODREJ FORK LIFT, ACE FORK LIFT ,TOYOTA FORK LIFT

BORE DIAMETER = 55
OUTER DIAMETER = 165
WIDTH = 45,  IMB BEARINGS,  Forklift roller bearings, or mast guide bearings, are designed to carry heavy loads and withstand high intermittent shock loads. Forklift bearings internal design maximizes load and protects the bearing component. This bearings have tight seals and high grease filling for minimal wear and tear


WHAT ARE BEARINGS - Bearings are "parts that assist objects' rotation bearings assist the shaft that rotates inside the machinery smoothly.Bearings are used in automobiles, airplanes, electric generators and so on. Also used in household appliances.The function of the Bearings is to rotating shafts of the wheels, gears, turbines, rotors, etc. in those machines, allowing them to rotate more smoothly.. The function of the bearings is to reduce friction, make rotation smoother and to protect the part that supports the rotation, and maintain the correct position for the rotating shaft. DIFFERENT TYPES OF BEARINGS –IMB-  Ball bearings, Taper, Cylindrical, Spherical, Kingpin, Needle and DAC Bearings.WHAT ARE TAPER BEARINGS AND ITS FUNCTIONS – Tapered roller bearings supports axial forces, as well as radial forces. The taper bearings consist of Cone, Cup, Cage and Rollers. Tapered roller bearings are made up of cone assembly and a cup. The cone assembly consists of the inner ring, the rollers, and a cage that retains and evenly spaces the rollers. The cup is simply the outer ring. Internal clearance is established during mounting by the axial position of the cone relative to the cup, although preloaded installations without clearance are common.IMB Cylindrical Roller Bearings – As name suggest the rollers are in cylindrical in shape. This bearings are design for heavy machinery and equipment. This bearings can support heavy radial load. The linear contact area with outer rings, helps distributing load on broader area or surface.Hub units – Also known as wheel bearing hubs, are critical part of the vehicle suspension system that allow the wheel to rotate smoothly and also support the vehicle’s weight. Available in as insert repair unit and repair unit. Hub unit contain two taper roller bearings, are pre-adjusted, greased and sealed at the factory in order to simplify installation. Truck Hub Units are double-row tapered roller bearings with separate cones held together by a retention ring and assembled in a one-piece outer ring.IMB - DAC BEARINGS- DAC bearing are Double Row Angular Contact Ball bearings, these are used in passenger cars, DAC bearing are used in automotive axles to guide rotation and load bearing parts. Normally they are available with oil seal, grease and available in ABC.

IMB BEARINGS FOR- FORK LIFT BEARINGS MAST BEARINGS VOLTAS FORK LIFT, GODREJ FORK LIFT, ACE FORK LIFT ,TOYOTA FORK LIFT

BORE DIAMETER = 45
OUTER DIAMETER = 119
WIDTH = 29,   IMB BEARINGS,  Forklift roller bearings, or mast guide bearings, are designed to carry heavy loads and withstand high intermittent shock loads. Forklift bearings internal design maximizes load and protects the bearing component. This bearings have tight seals and high grease filling for minimal wear and tear


WHAT ARE BEARINGS - Bearings are "parts that assist objects' rotation bearings assist the shaft that rotates inside the machinery smoothly.Bearings are used in automobiles, airplanes, electric generators and so on. Also used in household appliances.The function of the Bearings is to rotating shafts of the wheels, gears, turbines, rotors, etc. in those machines, allowing them to rotate more smoothly.. The function of the bearings is to reduce friction, make rotation smoother and to protect the part that supports the rotation, and maintain the correct position for the rotating shaft. DIFFERENT TYPES OF BEARINGS –IMB-  Ball bearings, Taper, Cylindrical, Spherical, Kingpin, Needle and DAC Bearings.WHAT ARE TAPER BEARINGS AND ITS FUNCTIONS – Tapered roller bearings supports axial forces, as well as radial forces. The taper bearings consist of Cone, Cup, Cage and Rollers. Tapered roller bearings are made up of cone assembly and a cup. The cone assembly consists of the inner ring, the rollers, and a cage that retains and evenly spaces the rollers. The cup is simply the outer ring. Internal clearance is established during mounting by the axial position of the cone relative to the cup, although preloaded installations without clearance are common.IMB Cylindrical Roller Bearings – As name suggest the rollers are in cylindrical in shape. This bearings are design for heavy machinery and equipment. This bearings can support heavy radial load. The linear contact area with outer rings, helps distributing load on broader area or surface.Hub units – Also known as wheel bearing hubs, are critical part of the vehicle suspension system that allow the wheel to rotate smoothly and also support the vehicle’s weight. Available in as insert repair unit and repair unit. Hub unit contain two taper roller bearings, are pre-adjusted, greased and sealed at the factory in order to simplify installation. Truck Hub Units are double-row tapered roller bearings with separate cones held together by a retention ring and assembled in a one-piece outer ring.IMB - DAC BEARINGS- DAC bearing are Double Row Angular Contact Ball bearings, these are used in passenger cars, DAC bearing are used in automotive axles to guide rotation and load bearing parts. Normally they are available with oil seal, grease and available in ABC.

FORK LIFT BEARINGS MAST BEARINGS VOLTAS FORK LIFT, GODREJ FORK LIFT, ACE FORK LIFT ,TOYOTA FORK LIFT.
GODREJ 3 TON
DIMENSION:
ID:35
OD:89
WEIDTH:29,     Forklift roller bearings, or mast guide bearings, are designed to carry heavy loads and withstand high intermittent shock loads. Forklift bearings internal design maximizes load and protects the bearing component. This bearings have tight seals and high grease filling for minimal wear and tear


WHAT ARE BEARINGS - Bearings are "parts that assist objects' rotation bearings assist the shaft that rotates inside the machinery smoothly.Bearings are used in automobiles, airplanes, electric generators and so on. Also used in household appliances.The function of the Bearings is to rotating shafts of the wheels, gears, turbines, rotors, etc. in those machines, allowing them to rotate more smoothly.. The function of the bearings is to reduce friction, make rotation smoother and to protect the part that supports the rotation, and maintain the correct position for the rotating shaft. DIFFERENT TYPES OF BEARINGS –IMB-  Ball bearings, Taper, Cylindrical, Spherical, Kingpin, Needle and DAC Bearings.WHAT ARE TAPER BEARINGS AND ITS FUNCTIONS – Tapered roller bearings supports axial forces, as well as radial forces. The taper bearings consist of Cone, Cup, Cage and Rollers. Tapered roller bearings are made up of cone assembly and a cup. The cone assembly consists of the inner ring, the rollers, and a cage that retains and evenly spaces the rollers. The cup is simply the outer ring. Internal clearance is established during mounting by the axial position of the cone relative to the cup, although preloaded installations without clearance are common.IMB Cylindrical Roller Bearings – As name suggest the rollers are in cylindrical in shape. This bearings are design for heavy machinery and equipment. This bearings can support heavy radial load. The linear contact area with outer rings, helps distributing load on broader area or surface.Hub units – Also known as wheel bearing hubs, are critical part of the vehicle suspension system that allow the wheel to rotate smoothly and also support the vehicle’s weight. Available in as insert repair unit and repair unit. Hub unit contain two taper roller bearings, are pre-adjusted, greased and sealed at the factory in order to simplify installation. Truck Hub Units are double-row tapered roller bearings with separate cones held together by a retention ring and assembled in a one-piece outer ring.IMB - DAC BEARINGS- DAC bearing are Double Row Angular Contact Ball bearings, these are used in passenger cars, DAC bearing are used in automotive axles to guide rotation and load bearing parts. Normally they are available with oil seal, grease and available in ABC.